However, with the improvement and development of industry technology, the advantages of assembly will become more and more prominent ~ what is the construction technology of assembly decoration? Before talking about the process, let’s take a look at the fabricated construction system, which is divided into 8 systems: integrated bathroom system, integrated kitchen system, integrated ceiling system, integrated wall system, integrated ground system, ecological door and window system, quick installation water supply system and thin method drainage system.

Most of the products with unified quality and assembled decoration are made by the factory, with unified models, specifications and design standards, so that the decoration project can be productized.

Wall coating plate; 2.

Key points: ① setting out must be carried out according to the drawings to ensure the consistency of indoor room size, the order of typesetting and the consistency of design and color direction.

During installation, the wall height shall be measured and measured, the structural adhesive shall be pasted, and the masking paper shall be temporarily reinforced.

In the process, today we mainly introduce the most commonly used walls, floors and roofs.

install the keel.

So the question comes ~ why is the prefabricated decoration so good and not widely used? There are three main reasons: A.

The comprehensive cost is low, the scale effect is obvious, the product cost is reduced and the labor cost is saved.

there is no problem with this understanding, but it is not all right.

“Shang” shaped aluminum alloy keel E and skirting line are processed and installed according to the side length of the room after the floor is completed.

Ceiling coating plate; 3.

② After the wall keel is completed, the size of the deep room must be checked again to ensure that it meets the size of the drawing.

It can not be touched until 24h after cleaning the overflow adhesive.

due to the small market scale and the insufficient supply of assembly workers, the price is still higher than that of traditional decoration.

Install the aluminum strip at the external corner of the wall.

In short, it is a decoration form in which the roof, wallboard, ground base and surface are prefabricated in the factory, and the required special assembly parts are prefabricated, and then the finished products are transported to the construction site and assembled by dry construction method.

△ schematic diagram of nail expansion principle, the general specification of hanging plate keel is 38 * 10 * 0.6mm, five on each wall, and the spacing is subject to the drawing.

Let’s talk about it specifically: 1.

Compared with traditional decoration, what are its characteristics? 1.

The wall construction process is: base treatment → setting out → drilling and planting expansion nails → installing keel → installing wallboard → installing top line → installing skirting → installing external corner aluminum.

Install the top line.

Energy saving and environmental protection prefabricated decoration adopts calcium silicate composite board, rock wool and other environmental protection materials.

High time efficiency, assembly construction is simpler than traditional construction, and only assembly is needed on site.

After the ceiling emulsion paint is completed, the top line shall be processed according to the side length of the room, and special connectors shall be pasted at the joints during installation.

However, the understanding of the assembly type may be vague.

b.

2.

For the owner, it’s like buying an Apple phone.

△ wall construction node a, base course treatment, setting out, drilling and planting expansion nails B.

4.

The so-called dry construction method is a construction method of anhydrous operation, which realizes the separation of pipeline and main structure through overhead design.

What he buys is what he gets.

Hang the “several” shaped aluminum alloy coated side keel along the upper edge of the wall coating plate, and the side keel and the covering plate shall be firmly fixed.

“Several” shaped aluminum alloy keel; 4.

The aluminum profile at the external corner of the wall shall be cut neatly and straight without burr.

What is the construction technology of prefabricated decoration? What is assembly decoration? Assembly decoration, also known as industrial decoration, is a decoration process in which industrial workers adopt dry construction according to standardized procedures through reliable assembly of parts and components produced in industrialization.

Wall construction process.

c.

Compared with traditional decoration, what are its advantages? 3.

What is prefabricated decoration? 2.

First install the top and bottom keels, buckle the keel on the expansion plug and insert the supporting screws.

These problems need to be solved urgently.

Install the side keel after the construction of the side keel covering plate is completed.

a.

3.

d.

f.

The ecological development of the industry lags behind, the design, production and construction are generally separated, and the coordination and integration is difficult, resulting in the extension of the construction period.

2.

The internal and external corners of the side keel shall be cut for 45 ° splicing, and the joints shall be tight..

It is the contradiction between personalization and scale.

The probability is that he won’t make mistakes.

Install the wallboard according to the drawing number and positioning, and pay attention to the overlapping relationship and installation sequence.

The hardbound house is well understood, that is, when the developer delivers the house, the house is fully decorated, and the owner can live as long as he adds some furniture, which is the so-called “Bag check-in”.

They think that the assembly type is the disassembly of modules, assembly, etc.

The construction sequence is generally: first the wall surface, then the top surface, and finally the ground.

Erection Anchor One Sided

Based on a 50 ㎡ house, the construction period of prefabricated decoration is about 6 days, while that of traditional decoration is 30 days, and the construction efficiency is significantly improved.

1.

What is the specific situation? Let’s talk today, mainly to solve the following three problems: 1.

At the 2020 Shenzhen International hardbound Housing Exhibition, the organizers used 24h to record the whole process of prefabricated decoration from construction to decoration.

Different from the previous situation that cement sand flies all over the site, it can not only keep the construction site clean, but also accelerate the follow-up construction.

All on-site installation adopts dry construction, which will not cause secondary pollution, waste and pollution.

Chengyao, the original author of DOP design (ID: dopdesign) and editor of Chengyao, “prefabricated decoration” is a very cutting-edge and hot word in the field of interior design in recent years, especially now that the hardbound house is promoted.

Construction process of top surface: install side keel along the upper edge of cladding plate → concealed inspection of water and electricity pipeline in ceiling → lay initial ceiling plate → install transverse keel → lay subsequent ceiling plate and keel → close up of lamps and other equipment → ceiling plate adjustment → edge closing and cleaning.

c.